Is this the Place? - Striper Talk Striped Bass Fishing, Surfcasting, Boating

Diggin Jiggin · 01-03-2010, 10:08 AM

Quote:

Originally Posted by Tagger

Don't scew them up ... take some time and make a sled ... Take one of those blanks and rip it in half . Lay it on a block of wood like a darter blank and trace ,(bandsaw),leave some stock in the back (arse of plug).. mark where you want your belly hole .. On sled drill out belly hole and glue in a 3/8 dowel there or whatever you, you use for a belly hole .. In back of sled drill hole where the arse hole of plug is .. Now pre drill belly/arse of blanks ,, slip belly hole of blank over the dowel and screw the arse with and 1.5 drywall screw .. Blank should be held firmly in the sled so you can make square cuts at 90 degrees ..(bandsaw),, Make a pattern ,, trace darter profile,, leave a little line .. touch up beltsander to line ..

Funny enough the band saw is not my issue.
The two problems I have is getting the table saw cut just the right height in relation to the thru hole and then sanding the bevel after the bandsaw cut. Sometimes I swear if I look with the left eye they tilt one way, try the right eye and its tilted the other. Back and forth we go...

Tagger · 01-03-2010, 10:15 AM

Quote:

Originally Posted by Diggin Jiggin

Funny enough the band saw is not my issue.
The two problems I have is getting the table saw cut just the right height in relation to the thru hole and then sanding the bevel after the bandsaw cut. Sometimes I swear if I look with the left eye they tilt one way, try the right eye and its tilted the other. Back and forth we go...

all on the bandsaw Dave ,, no table saw ..try it .. hold your sled flat on the table ,,cut beak,slope,, everything .. key is your blank firmly in sled,,then its just along for the ride

Diggin Jiggin · 01-03-2010, 11:00 AM

Quote:

Originally Posted by Tagger

all on the bandsaw Dave ,, no table saw ..try it .. hold your sled flat on the table ,,cut beak,slope,, everything .. key is your blank firmly in sled,,then its just along for the ride

Thats a good idea Eddie. I'll have to try that.

eastendlu · 01-03-2010, 11:34 AM

Morning all i have been off all week and forgot what day it was

.

numbskull · 01-03-2010, 10:15 AM

Quote:

Originally Posted by Diggin Jiggin

Sometimes I swear if I look with the left eye they tilt one way, try the right eye and its tilted the other. Back and forth we go...

EXACTLY TRUE!!!!!!!!!. I resanded a whole batch of darters last year then figured out my glasses make them twist depending on which eye I sight them with.

Eddy's jig is the way to go, but you need a vertical beltsander since the jig will be on its side.

Tagger · 01-03-2010, 10:26 AM

Quote:

Originally Posted by numbskull

Eddy's jig is the way to go, but you need a vertical beltsander since the jig will be on its side.

I just have a hand held BS cleated on the side of the bench .. If your bandsaw blade is decent you barely have to touch them ..

numbskull · 01-03-2010, 10:34 AM

Quote:

Originally Posted by Tagger

I just have a hand held BS cleated on the side of the bench .. If your bandsaw blade is decent you barely have to touch them ..

I've got BS all over the place, but it doesn't help. Does that mean I need a new bandsaw?

Backbeach Jake · 01-03-2010, 10:37 AM

Like minds...
Reminds me I gotta go shovel..snow. And get to the JakeCave. Catch you later and thanks for today's lessons..

mfm22 · 01-03-2010, 10:59 AM

George looks like you have a nice start to the "lipless" .
where did you get ideas on proto ? what type of wood?

I just turned some musso 6" swimmers and some spin's . Started to make a few BM Schoolie's. Not sure of their fish catching ability ?
That lipless has peaked my curiosity along with your predator knockoffs

eastendlu · 01-03-2010, 11:35 AM

Quote:

Originally Posted by numbskull

I've got BS all over the place, but it doesn't help. Does that mean I need a new bandsaw?

What bandsaw do you have as it might just need some tuning.

numbskull · 01-03-2010, 12:40 PM

Quote:

Originally Posted by eastendlu

What bandsaw do you have as it might just need some tuning.

You're still asleep. That was tongue in cheek. I've got a Rockwell 14" (not to mention an ancient 20" Porter Cable in pieces), it could use some tuning (new tires), but everything else is set right. Even with high tension on a high count skip tooth blade (dressed with a stone and running in cool blocks) I don't get smooth enough cuts in maple to avoid sanding.

Eddy has a little bench top delta (I think) with a very thin kerf blade and very high speed. Does a better job for most plug building chores than my real saw. If I had someplace to put it I'd buy one just to do lip slots.

Tagger · 01-03-2010, 02:07 PM

Quote:

Originally Posted by numbskull

Eddy has a little bench top delta (I think) with a very thin kerf blade and very high speed. Does a better job for most plug building chores than my real saw. If I had someplace to put it I'd buy one just to do lip slots.

Thats true ,, little Delta is pissa ($100.00)... I have a larger floor model Delta brandy new I rarely use ,, Its got the power but the speed on the little bench model does a better job .

Sgt Striper · 01-03-2010, 10:19 AM

Good morning and Happy New Year to everyone!! Just got up, kinda lazy today. Was away for the past week and will probably work on the large Nike again ( trying to get some 8/4 cedar or pine) Small one is done and is ready for paint. Next project is to finish up large surfster and work on some pikies. Going to use original C.C. paint schemes on them.
Got some Tiger maple when I was out in Pa. last week and will be concentrating on finishing a Huntboard I started months ago, and finishing two Shaker sewing tables I also have sitting around, so the plugbuilding will be on hold a few weeks.

Tagger · 01-03-2010, 10:29 AM

Quote:

Originally Posted by Sgt Striper

Good morning and Happy New Year to everyone!! Just got up, kinda lazy today. Was away for the past week and will probably work on the large Nike again ( trying to get some 8/4 cedar or pine)

Happy New year Sgt. ... sorry ,,. unless your a truck driver and your near stoughton ma. (downes and reader) ,, Don't know resources in NJ ..

Sgt Striper · 01-03-2010, 10:35 AM

Quote:

Originally Posted by Tagger

Happy New year Sgt. ... sorry ,,. unless your a truck driver and your near stoughton ma. (downes and reader) ,, Don't know resources in NJ ..

I know where I can get some but to lazy to take the ride, plus the prices on wood is starting to get out of control. The guy I get my AYC from has not ordered any in two months because of the price. The tiger maple I just got cost me $9.00 bf

, paid $7.00 bf about six months ago!